|
Standards: |
ASTM
C1186 – “Standard
Specification for Flat Fiber-Cement Sheets”
ASTM
E330 – “Standard Test Method for Structural Performance of Exterior
Windows, Doors, Skylights and Curtain Walls by Uniform Static Air
Pressure Difference”
ASTM E84 – “Standard Test
Method for Surface Burning Characteristics of Building Materials”
|
|
|
Markings: |
Product pallets to be marked with the following: Manufacturers’ Name,
Trademark or other recognized symbol of identification,
Product Model Designation, Month and Year of manufacture or
equivalent, City and Country of manufacture, QAI logo with
the “us” identifier, QAI listing number (B1034), The wording
“ASTM C1186”.
|
|
|
|
Models: |
TABLE 1 – Model Designations
|
|
Models
|
Model Designation
|
Width
|
Length
|
Thickness
|
|
Lap Siding
|
Smooth, Cedar, Beaded,
Dutch Lap
|
5 ¼”, 6 ¼”,
7 ¼”, 8 ¼”,
9 ¼”, 12”
|
12 feet
|
5/16”
|
|
Shapes / Shingles
|
Square Edge Straight, Square Edge Staggered, Half Rounds, Octagons
|
12” or 16”
|
4 feet
|
5/16”
|
|
Shakes
|
Individual Shakes
|
6 ¼”, 8 ¼”, 12”
|
16 inches
|
¼”
|
|
Soffit Panels
|
Cedar, Smooth, Ventilated,
Porch Panel
|
12”, 16”, 24”, 48”
|
8 feet and 12 feet
|
¼”
|
Plycem USA, Inc. Fiber Cement Boards meet all requirements of ASTM C1186; the product meets the requirements for Type A, Grade II.
|
TABLE 2 - ASTM E84 Flame Spread and Smoke Developed Ratings:
Product
|
Manufacturing Location
|
Thickness
|
Flame Spread Index (FSI):
|
Smoke Developed Index (SDI):
|
Plycem Allura™ Fiber Cement Products
|
North Wilkesboro, NC
|
¼” to ½”
|
0
|
0
|
White City, OR
|
¼” to ½”
|
0
|
0
|
The Maximum Design Pressures for specific fasteners and installation details are shown in the tables of this listing below. The
installation of Fiber Cement Boards must be in accordance with the manufacturer’s installation instructions and the fastening requirements
in the table. This listing does not address the applicability of use in areas where wind speeds exceed the maximum design pressures shown
in the Tables below.
For edge distances, fasteners should not be used closer than ½” to the edges of the fiber cement products. All fasteners should be
installed flush with the surface (no distance between the bottom of the head, and not over-driven past the surface of the panels).
|
TABLE 3 – PRESSURE RESISTANCE PER ASTM E330 - TEST RESULTS
Config. Number
|
Product
|
Product Size
|
Fastener
|
Fastener Spacing
|
Framing
|
Frame OC
|
Sheathing
|
Maximum Design Pressure
(psf)
|
1
|
Vertical Siding
|
4′ x 8′
|
SFS Intec TW-S-D12 4.8 x 38 1-1/2′′ x 0.4675′′ Head
|
Commercial Pattern A
|
Wood SPF
|
16”
|
7/16” OSB
|
31.1
|
2
|
Vertical Siding
|
4′ x 8′
|
SFS Intec TW-S-D12 4.8 x 38 1-1/2′′ x 0.4675′′ Head
|
Commercial Pattern B
|
Wood SPF
|
16”
|
7/16” OSB
|
21.7
|
3
|
Vertical Siding
|
4′ x 8′
|
6D Common Nail 2” Long x 0.095” Shank x 0.235” Head
|
6′′ Edge, 6" Field
|
Wood SPF
|
16″
|
None
|
42.2
|
4
|
Vertical Siding
|
4′ x 8′
|
6D Common Nail 2`` Long x 0.095`` Shank x 0.235`` Head
|
6′′ Edge, 12′′ Field
|
Wood SPF
|
16″
|
None
|
21.1
|
5
|
Vertical Siding
|
4′ x 8′
|
#8 1-5/8′′ Long x 0.375′′ Ribbed Wafer Head Screws
|
6′′ Edge, 12′′ Field
|
Steel 20 ga
|
16”
|
1/2" Gypsum Board
|
42.4
|
6
|
Vertical Siding
|
4′ x 8′
|
#8 1-5/8′′ Long x 0.375′′ Ribbed Wafer Head Screws
|
6′′ Edge, 12′′ Field
|
Steel 20 ga
|
24”
|
1/2" Gypsum Board
|
24.1
|
7
|
Shingles
|
8 ¼”
|
Roofing Nail 1-3/4′′ Long x 0.120′′ Shank x 0.375′′
|
Blind Nailed
|
Wood SPF
|
16”
|
7/16” OSB
|
31.3
|
8
|
Shapes
|
15 ¾″ (7″reveal)
|
Ring-Shank Roofing Nails 1-3/4″ x 0.120 shank x 0.375 Head
|
As per instructions; 5 fasteners per full-size piece
|
Wood SPF
|
16”
|
7/16” OSB
|
22.7
|
9
|
Shapes
|
15 ¾″ (7″reveal)
|
6D Ring Shank Nail 1-1/2′′ Long x 0.095′′ Shank x 0.235 Head
|
As per instructions; 5 fasteners per full-size piece
|
Wood SPF
|
16”
|
7/16” OSB
|
34.3
|
10
|
Shapes
|
15 ¾″ (7″reveal)
|
6D Common Nail 2” Long x 0.095” Shank x 0.235”Head
|
As per instructions; 5 fasteners per full-size piece
|
Wood SPF
|
16”
|
7/16” OSB
|
21.4
|
11
|
Shapes
|
15 ¾″ (7″reveal)
|
0.100′′ x 2.0′′ Long Knurled Pins, 0.3125′′ Head ET&F #AGS -100-0200NA
|
As per instructions; 5 fasteners per full-size piece
|
Steel 20 ga
|
16”
|
1/2" Gypsum Board
|
27.7
|
12
|
Shapes
|
15 ¾″ (7″reveal)
|
#8 1-5/8′′ Long x 0.375′′ Ribbed Wafer Head Screws
|
As per instructions; 5 fasteners per full-size piece
|
Steel 20 ga
|
16″
|
7/16” OSB
|
33.4
|
13
|
Lap Siding
|
9 ¼”
|
Ring-Shank Roofing Nails 1-3/4″ x 0.120 shank x 0.375 Head
|
Blind Nailed, at 8” oc
|
Wood SPF
|
24”
|
7/16” OSB
|
32.3
|
14
|
Lap Siding
|
9 ¼”
|
Ring-Shank Roofing Nails 1-1/4″ x 0.120 shank x 0.375 Head
|
Blind Nailed, at 8” oc
|
Wood SPF
|
24”
|
7/16” OSB with Furring Strips
|
39
|
15
|
Lap Siding
|
9 ¼”
|
Ring-Shank Roofing Nails 1-1/4″ x 0.120 shank x 0.375 Head
|
Blind Nailed, at 12” oc
|
Wood SPF
|
24”
|
7/16” OSB with Furring Strips
|
20.3
|
16
|
Lap Siding
|
9 ¼”
|
6D Common Nail 2″ Long x 0.095″ Shank x 0.235″ Head
|
Face Nailed
|
Wood SPF
|
16”
|
None
|
24.5
|
17
|
Lap Siding
|
9 ¼”
|
6D Common Nail 2” Long x 0.095” Shank x 0.235” Head
|
Face Nailed, at 12” oc
|
Wood SPF
|
24”
|
7/16” OSB
|
24.4
|
18
|
Lap Siding
|
9 ¼”
|
6D Common Nail 2” Long x 0.095” Shank x 0.235” Head
|
Face Nailed, at 8" oc
|
Wood SPF
|
16”
|
7/16” OSB
|
48.7
|
19
|
Lap Siding
|
8 ¼”
|
Roofing Nail 1-3/4′′ Long x 0.120′′ Shank x 0.375′′
|
Blind Nailed
|
Wood SPF
|
16”
|
None
|
23.3
|
20
|
Lap Siding
|
8 ¼”
|
Ring-Shank Roofing Nails 1-3/4″ x 0.120 shank x 0.375 Head
|
Blind Nailed, at 8” oc
|
Wood SPF
|
24”
|
7/16” OSB
|
40.3
|
21
|
Lap Siding
|
8 ¼”
|
Ring-Shank Roofing Nails 1-3/4″ x 0.120 shank x 0.375 Head
|
Blind Nailed, at 12” oc
|
Wood SPF
|
24”
|
7/16” OSB
|
27
|
Config. Number
|
Product
|
Product Size
|
Fastener
|
Fastener Spacing
|
Framing
|
Frame OC Spacing
|
Sheathing
|
Maximum Design Pressure
(psf)
|
22
|
Lap Siding
|
8 ¼”
|
Ring-Shank Roofing Nails 1-3/4″ x 0.120 shank x 0.375 Head
|
Blind Nailed, at 8” oc
|
Wood SPF
|
16”
|
7/16” OSB
|
37.6
|
23
|
Lap Siding
|
8 ¼”
|
6D Common Nail 2″ Long x 0.095″ Shank x 0.235″ Head
|
Face Nailed
|
Wood SPF
|
16”
|
None
|
25.8
|
24
|
Lap Siding
|
8 ¼”
|
#8 1-5/8’’ Long x 0.375’’ Ribbed Wafer Head Screws
|
Blind Screwed
|
Steel 20 ga
|
16”
|
None
|
22.3
|
25
|
Lap Siding
|
7 ¼”
|
Roofing Nail 1-3/4′′ Long x 0.120′′ Shank x 0.375′′
|
Blind Nailed
|
Wood SPF
|
16”
|
None
|
31.4
|
26
|
Lap Siding
|
7 ¼”
|
6D Common Nail 2″ Long x 0.095″ Shank x 0.235″ Head
|
Face Nailed
|
Wood SPF
|
16”
|
None
|
33.2
|
27
|
Lap Siding
|
7 ¼”
|
6D Common Nail 2” Long x 0.095” Shank x 0.235” Head
|
Face Nailed, at 8" oc
|
Wood SPF
|
16”
|
7/16” OSB
|
65.7
|
28
|
Lap Siding
|
6 ¼”
|
Roofing Nail 1-3/4′′ Long x 0.120′′ Shank x 0.375′′
|
Blind Nailed
|
Wood SPF
|
16”
|
None
|
36.4
|
29
|
Lap Siding
|
6 ¼”
|
6D Common Nail 2″ Long x 0.095″ Shank x 0.235″ Head
|
Face Nailed
|
Wood SPF
|
16”
|
None
|
34.8
|
30
|
Lap Siding
|
5 ¼”
|
Roofing Nail 1-3/4′′ Long x 0.120′′ Shank x 0.375′′
|
Blind Nailed
|
Wood SPF
|
16”
|
None
|
38.3
|
31
|
Lap Siding
|
5 ¼”
|
6D Common Nail 2″ Long x 0.095″ Shank x 0.235″ Head
|
Face Nailed
|
Wood SPF
|
16”
|
None
|
43.7
|
32
|
Lap Siding
|
12”
|
6D Common Nail 2” Long x 0.095” Shank x 0.235” Head
|
Face Nailed
|
Wood SPF
|
16”
|
7/16” OSB
|
36.1
|
33
|
Individual Shakes
|
18” (8” Reveal)
|
Roofing Nail 1-1/2′′ Long x 0.120′′ Shank x 0.375′′
|
2 nails per shake
|
Wood SPF
|
24”
|
7/16” OSB
|
31.3
|
34
|
Individual Shakes
|
18” (8” Reveal)
|
6D Common Nail 2” Long x 0.095” Shank x 0.235” Head
|
2 nails per shake
|
Wood SPF
|
24”
|
7/16” OSB
|
27.1
|
|
|
|
The materials, products or systems listed in this directory have
been qualified to bear the QAI Listing Mark under the conditions
stated with each Listing. Only those products bearing the QAI
Listing Mark are considered to be listed by QAI.
No warrantee is expressed or implied, and no guarantee is
provided that any jurisdictional authority will accept the Listing
found herein. The appropriate authorities should be contacted
regarding the acceptability of any given Listing.
Questions regarding this listing may be directed to
info@qai.org. Please include the
listing number in the request. |
|