Construction CEG Inc.
Factory Built Structures Listing Program
- Construction CEG Inc.
- Modular Homes
- Matane, Quebec
- REC787-1
- REC787-1, Edition 2
- June 6, 2022
- August 20, 2024
- N/A
-
CSA A277 “Procedure for Factory Certification of Prefabricated Buildings, Modules, and Panels”
Quebec Construction Code, Chapter I – Building (NBC with Quebec amendments), Part 9
National Building Code of Canada, Part 9
National Plumbing Code of Canada
CSA C22.10 Québec Construction Code, Chapter V – Electricity (Canadian Electrical Code, Part I, “Safety Standard for Electrical Installations” with Quebec amendments)
CSA C22.1 Canadian Electrical Code, Part I, “Safety Standard for Electrical Installations”
CSA B149.1 “Natural Gas and Propane Installation Code”
Note 1: Unless otherwise specified, the Standards and Codes noted are the most current versions in effect.
Note 2: Various provinces and territories have amendments to the national building code, jurisdictions may require structures to comply with provincial/municipal codes in lieu of the national building codes, the local AHJ should be consulted on the applicable requirements”
-
Product: Modular Homes
Note 3: Products may be labelled under a separate brand name “Concept Mat”
-
All markings must be permanent and visible after installation.
1. The QAI label (item 1067, black with gold, 3-1/2” diameter) is normally located in close proximity to the electrical panel and includes:− Certification label serial number
− QAI certification logo with the “C” Identifier
− “Modular Homes”QAI logo shown here:
2. The specification nameplate (item 1068, 8-1/2” x 14” size) is located in close proximity to the electrical panel and includes:
− Manufacturer’s Name and Address
− Date of Manufacture
− Model Serial Number or Product Code
− Foundation Type (Perimeter Foundation Wall or Piers)
− Floor live Load
− Specified Snow Load (1/50)
− Seismic Response Sa (0.2)
− Hourly Wind Pressure (1/50)
− Envelope Effective Thermal Resistance
− Windows/Doors/Skylights Thermal Characteristics
− Outside Design Temperature (Heal Loss or Heat Gain)
− Factory Installed Appliances
− Site Installed Components, Assemblies, and Systems
− Electrical Systems Voltage, Frequency, and Amperage3. Other Markings as required by the relevant codes.
Note 4: The QAI label and specification nameplate are available from QAI and must be applied at the factory.
-
Single family dwellings classified under one major occupancy (Group C – Residential), constructed in single modules single storey configuration. Modular homes under this scope have a building area not exceeding 600m2.
Residential buildings are designed and constructed within the limitations of Part 9 without fire and sound separations. This listing does not include multi-residential buildings requiring fire and sound separation or shared egress facilities, hotels and motels, and/or any buildings designed with multiple major occupancies.
For a full list of structures covered under this occupancy please refer to Notes to Part 3, A-3.1.2.1.(1) Major Occupancy Classification in the Quebec Construction Code, Chapter I – Building and National Building Code.
Structural:
Conventional Wood Frame Construction within the limitations of Part 9 of the Quebec Construction Code, Chapter I – Building. Structures may be built over structural steel support frame.
Electrical Ratings:
120/240V, 60Hz, 200A Max.
Heating/Ventilation:
Central Forced Air Furnaces. Units may be Electric, Natural Gas or LPG Fired. Modules may be equipped with electrical baseboard heaters and air conditioning.
Plumbing:
Conventional drainage and venting systems to a maximum of 240 hydraulic fixture units.
Gas Systems:
Modules may be equipped with gas or LPG appliances and equipment.
Notes:
Structures included in this listing are manufactured at a central facility and transported to the site. These modules include provisions for on-site interconnections, connection to on-site services: water and sewage, gas/LPG and electrical power supply. QAI certification covers the construction of the structures including any factory installed electrical services, equipment and fixtures. QAI certification is intended to obviate the necessity of further inspection by the local regulatory authorities except for site connections to services or to other modules and for site installed features.
Site installation of products must be done according to manufacturer’s installation instructions and in compliance with the requirements set by the local authority having jurisdiction.
The materials, products or systems listed in this directory have been qualified to bear the QAI Listing Mark under the conditions stated with each Listing. Only those products bearing the QAI Listing Mark are considered to be listed by QAI.
The standard herein listed is the currently accepted version within the relevant certification scheme, code or other requirements unless otherwise noted. Transition periods may apply. Upon request, QAI will provide information about the validity of any of its certifications.
No warrantee is expressed or implied, and no guarantee is provided that any jurisdictional authority will accept the Listing found herein. The appropriate authorities should be contacted regarding the acceptability of any given Listing.
Visit the QAI Online Listing Directory located at www.qai.org for the most up to date version of this Listing and to validate that this QAI Listing is active. Questions regarding this listing may be directed to info@qai.org. Please include the listing number in the request.
USA 
Canada 
Europe 
China 
S Korea